1. The gas generator set with good low temperature performance is selected, which has small viscosity at low temperature, good lubrication between friction pairs and small starting resistance, which is conducive to start-up. For example, the smaller the number before 15W / 40W, the better the low-temperature fluidity of the oil. Therefore, 10W or 5W oil is recommended at low temperature.

2、采用低温性能好的蓄电池必要时可对蓄电池进行保温，以保证其低温条件下能正常充电且有足够的输出电流，从而提高了启动系统功率。

2. The battery with good low temperature performance can be insulated if necessary to ensure that it can be charged normally and has enough output current under low temperature conditions, so as to improve the power of starting system.

瓦斯发电机组有哪些常见的低温启动方式

What are the common low temperature start-up methods of gas generator set

瓦斯发电机组有哪些常见的低温启动方式

What are the common low temperature start-up methods of gas generator set

3、加注冷起动液。

3. Fill in cold starting fluid.

4、火焰预热启动。

4. The flame is preheated and started.

5、循环水加热系统(也称燃油加热器加热系统)。

5. Circulating water heating system (also known as fuel heater heating system).

6、其他的预热方式 除上述预热方式外，还可采用热水预热法、蒸气预热法、电预热法等多种方法进行低温启动。

6. In addition to the above preheating methods, other preheating methods can also be used, such as hot water preheating method, steam preheating method, electric preheating method, etc.

操作时，必须保证箱式变电站低压进线开关处于断开位置，机组油、水、合上预供油开关，启动电动预供油泵(或扳动手摇机油泵)。待主油道压力达100kPa启动要求值后，按下起动按钮“Start”，机组起动后，可按下“翻页"按钮，通过液晶显示屏检查发动机运行中各项技术参数的变化。起动成功后应怠速暖机，当机油温、水温达到40℃以上，方可加速、加载。

During operation, it is necessary to ensure that the low-voltage incoming line switch of the box type substation is in the off position, the oil, water and pre oil supply switches of the unit are closed, and the electric pre supply oil pump (or the manual oil pump) is started. When the pressure of main oil passage reaches the required value of 100KPA, press the start button "start". After the unit starts, press the "page turning" button to check the changes of various technical parameters during engine operation through LCD. After successful start-up, the engine should be warmed up at idle speed. Only when the oil temperature and water temperature reach above 40 ℃, can the engine be accelerated and loaded.

按动或调节控制屏上加减速旋钮调整机组的频率，使之略高于额定频率。调整控制屏上的电压调节器的微调旋钮，使交流电压表在400V位置，按下“I/O”按钮，此时在站控室SCADA监控界面上“发电机”栏中可监控相关数据，机组便向负载供电。

Press or adjust the acceleration and deceleration knob on the control panel to adjust the frequency of the unit to make it slightly higher than the rated frequency. Adjust the fine adjustment knob of voltage regulator on the control panel to make the AC voltmeter at 400V and press the "I / O" button. At this time, the relevant data can be monitored in the "generator" column on the SCADA monitoring interface of the station control room, and the unit will supply power to the load.

本文由瓦斯发电机组整理发布，您是不是对这些内容有所了解了呢?更多的内容请点击：//www.gz-yanye.com我们会有更多精彩内容等你查看。

This article is organized and released by the gas generator set. Do you have any understanding of these contents? For more information, please click: //www.gz-yanye.com We'll have a lot more to see.