瓦斯发电机组开车前检查确认无误后才允许开车，这是使得发电机组正常运行的需要，也是对机组的维护保养措施，具体内容小编来介绍相关内容。

The gas generator set can only be started after it is checked and confirmed to be correct before starting, which is the need for the normal operation of the generator set and the maintenance measures for the unit. The specific contents are introduced in the sub series.

管系

Piping system

1、瓦斯气源管线与瓦斯机进气接口处须安装密封垫片并使得紧固可靠，应急手动停车阀门功能应可靠。

1. The sealing gasket must be installed at the interface between the gas source pipeline and the gas inlet of the gas machine to make it firm and reliable, and the function of the emergency manual shutdown valve should be reliable.

2、瓦斯管线的螺纹连接处须加缠密封胶带，焊接部位不得有气孔。

2. The threaded connection of gas pipeline must be wrapped with sealing tape, and the welding part must not have pores.

3、检查机房内管线是否漏气，如有泄漏，须处理后再开机。

3. Check whether the pipeline in the machine room leaks. If there is any leakage, it must be treated before starting the machine.

部件的安装

Installation of components

1、混合器法兰及蝶门轴颈径向间隙不得漏气。

1. The radial clearance of mixer flange and butterfly door journal shall be free of air leakage.

2、电磁阀、调压阀的连接不得松动漏气。

2. The connection of solenoid valve and pressure regulating valve shall not be loose or leak.

3、各防爆装置的易熔易爆膜片须按照技术设计要求安装，不得随意更换材料或加厚。

3. The fusible and explosive diaphragm of each explosion-proof device must be installed according to the technical design requirements, and it is not allowed to change materials or thicken at will.

4、瓦斯发电机组和控制屏与电缆接头的连接须紧固可靠。

4. The connection between the gas generator set and the control panel and the cable connector must be firm and reliable.

传感器与控制屏组合模拟检测

Combined analog detection of sensor and control panel

1、油压检测：装有压力继电器的原动机，用压力校验仪检测设定值，检查控制屏是否分闸停机。装有监控仪的原动机，先自检，然后拆下信号输入线检查控制屏是否分闸停机。

1. Oil pressure detection: for the prime mover equipped with pressure relay, use the pressure calibrator to detect the set value and check whether the control panel is opened and shut down. For the prime mover equipped with a monitor, first conduct self-test, and then remove the signal input line to check whether the control panel is switched off and shut down.

2、油温、水温检测：将模拟检测好的传感器与传感器导线连接，把传感器放在排气管上加温，检测是否在设定值上分闸停机。

2. Oil temperature and water temperature detection: connect the analog detected sensor with the sensor wire, place the sensor on the exhaust pipe for heating, and detect whether the switch is opened and shut down at the set value.

3、检查发电机组气源应急阀门、电磁阀是否可靠。

3. Check whether the air source emergency valve and solenoid valve of the generator set are reliable.

4、减掉负载，合上短路器开关，把转速开关设置到额定转速位置，然后调整2301A速度控制器的额定转速电位器，缓慢顺时针旋转直至机组在设定

4. Reduce the load, close the breaker switch, set the speed switch to the rated speed position, then adjust the rated speed potentiometer of 2301a speed controller, and slowly rotate clockwise until the unit is set

值报警分闸、超速停机为止，然后将额定转速电位器逆时针复位到原来的位置。

Value alarm until opening and overspeed shutdown, and then reset the rated speed potentiometer counterclockwise to the original position.

机组

crew

1、开机前，应清理机组（旋转部件）上放置的杂物（如盘车杠、工具、螺钉等），以免开车时工件飞出去伤人。

1. Before starting the machine, the sundries (such as turning bar, tools, screws, etc.) placed on the unit (rotating parts) should be cleaned to prevent the workpiece from flying out and hurting people during driving.

2、开机前手动盘车时，注意先断开起动电源，以免误触动起动按钮，盘车杠飞出去伤人。

2. When turning manually before starting the machine, pay attention to disconnect the starting power first, so as not to touch the start button by mistake, and the turning bar will fly out and hurt people.

以上就是介绍的关于发电机组开车前，检查确认无误后才允许开车的相关内容，希望能给用户带来参考。更多内容的了解还是来网站//www.gz-yanye.com咨询吧。

The above is about the relevant content that the generator set is allowed to start up only after it is checked and confirmed to be correct before starting up. I hope it can bring reference to users. For more information, please visit the website //www.gz-yanye.com Consult.